![]() Dental Floss (or Fishing Line, or Thread)Įver think you’d use floss to fit a ring? If you have some dental floss, thread, or fishing line lying around, you may be able to use it to make your ring fit tighter. Nail polish doesn’t last long, especially if it’s under constant contact and friction every day. Just like with candle wax, this is a very temporary solution. Keep applying until a layer starts to build up. The key is to apply a thin coat on the inner ring shank. ![]() Yes, it’s another quick drying liquid that solidifies after drying, but you may be limited to how thick of a coating this method will produce, so try it out and see if it’s enough to fill the gap. If you’re going with this method, you’re better off using clear nail polish so it isn’t as obvious. Nail polish can be very effective for rings that are only slightly loose on your finger. I’ve done it several times and it works like a charm. My advice, though, is if you’re gonna go with one of these options, stick to candle wax. If you want to try this, squeeze a generous strip of glue directly (and carefully) onto the inside of the band. And it could potentially ruin the finish of your ring, depending on the ring’s material. I guess this could work, too, but seems even messier due to the stickiness factor. Liquid glue is another option people have used and documented on the internet. It doesn’t maintain it’s solid, one-piece state as easily. You can always shave away the excess dried wax, but it’s more difficult to add on wax after a layer has already dried. In my experience, it’s best to add more wax than less. Obviously, this will take some guesstimation, but do your best. Let it completely dry, and then put your ring on. So if you’re in a pinch, you may want to try this.Įssentially you light a candle, and when the wax starts to melt, carefully drip the wax onto the interior bottom of the ring. A slightly messier method, yes, but there’s also a good chance you have a candle laying around. ![]() Candle Wax (or Glue)Īnother method is to use candle wax. It depends on the type of rubber band you have, and the amount of thickness you need. So there we go, two ways you could use a rubber band to make your ring fit. Otherwise, it would stick out and be uncomfortable and unsightly and people will think you’re weird. If it’s too long, the excess would need to be cut off. You’ll have to find the right size rubber band. Method 2: You could take a rubber band and wrap it around the bottom of your ring (the portion that sits closest to your palm). You’ll have to make sure the rubber band isn’t too tight of a squeeze on your finger, since that can be painful and prevent blood circulation. The thickness of the clear rubber band will make up for the space between the ring and your finger. ![]() Method 1: You could use a tiny, transparent rubber band that will go on your finger, under the ring. There are two ways you could go about this. Ideally, a thin, transparent one, or one that is close to your skin tone, so it’s not obvious you’re using a rubber band to fit your ring to your finger. The Rubber Band WrapĪ truly DIY, albeit kinda janky, way to make your ring fit is to use a rubber band. Here are a handful of techniques to try (or products you may want to buy that will solve your problem). Sometimes, you want to have an impermanent, do-it-yourself solution that’s affordable and easy. How To Make a Big Ring Fit Better: A Few DIY Solutions Works with rings that are a finger size of 5.So if your ring keeps spinning or falling off your finger, here are a few techniques and products you can use when figuring out how to wear a ring that is too big.Spring ring guards are not intended to be used on rings shanks that graduate significantly in mm width. This style of a ring guard will only work with rings that are a finger size of 5.75 or larger. Notice: Spring Ring guards should be ordered based on the mm width of your ring/band. This method of sizing a ring is cost effective and avoids permanently changing a ring size by having to cut and re solder the shank. Simply put the ring guard inside the lower part of the band, fold over tabs to fit tightly to the band. Our Spring Ring Guards are self adjusting ring sizers allowing rings to adjust from 3/4 of a ring size up to 3 ring sizes smaller. The hidden leaf spring assures a firm even tension when fitting over knuckles, making it smooth and comfortable to wear. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |